Accessories Bicycles Parts Specials Tools View Cart

In West Newton Since 1952 - On The Web Since 1995

Visit our harriscyclery.net Catalog for a more Contemporary Shopping Experience.

Handlebar Stems from Harris Cyclery

For Threaded Forks/HeadsetsFor Threadless Forks/Headsets
1 Inch 1 1/8 Inch 1 1/4 Inch Stem Riser 1 Inch 1 1/8 Inch 1 1/4 Inch Stem Riser

spoke

 

Stems for 1" Threaded Forks

Stems listed in this section have standard 7/8" (22.2 mm) diameter quills, fit most higher quality bicycles made in the 20th century.

Exceptions: Older American bikes that use the 13/16" (21.15 mm) size-Click Here   |    Older French bikes that use the 22.0 size-Click Here

spoke

Nitto Technomic stems buy button

These are beautiful, Japanese-made forged aluminum stems with an extra tall column (225 mm overall.) Not as flexible as you were when you bought your bike? Want a more upright position without sacrificing the versatility of your drop bars? This is the ticket! These allow you to raise your handlebars about 2 1/2" higher than traditional stems.

These have a standard 22.2 mm (7/8") column which fits standard "one inch" fork steerers.

  • The 26.0 mm clamp fits most modern road handlebars (except the newer 31.8mm).

  • Shims are available for handlebars with 25.4mm center.

  • Sizes (Extention/reach): 50mm, 60mm, 70mm, 80mm, 90mm, 100mm, 110mm, 120mm
Nitto Technomic Stem Nitto Technomic stems

spoke

Nitto Dirt Drop Riser Stem buy button

The Dirt Drop is one of the few riser stems designed for drop handlebars.

The lower clamp section has slight cutaways on each side that allows a drop handlebar to pass through. These have a standard 22.2 mm (7/8") column which fits standard "one inch" fork steerers.

  • Extention: 80mm or 100mm
  • Quill Overall Length: 190mm
  • Clamp Diameter: 26.0mm
  • Quill Diameter: 22.2mm
  • Cold forged, heat-treated aluminum
  • Color: Silver

    26.0mm clamp is standard on most pre-2010 road handlebars.

    Not designed for rugged off-road use.

  • Nitto Dirt Drop Riser Stem


    spoke

    Kalloy Riser Stems buy button

    Aluminum stem with 17 degree rise. These have a standard 22.2 mm (7/8") column which fits standard "one inch" fork steerers.

  • Rise (angle up): 17 degrees
  • Reach (Extension): Current stock is 100mm only!
  • Clamp Diameter: 25.4mm
  • Quill Diameter: 22.2mm
  • Quill Overall Length: 180mm
  • Color: Silver

    25.4mm clamp is standard on most flat and riser handlebars.
    This stem will not work with drop handlebars.

  • Kalloy Riser Stem


    spoke


    Nitto shims

    Problem Solvers Handlebar Shims SM1070 buy button

    These shims let you use a standard 25.4 mm (1 inch) diameter handlebar in an Italian size (26.0 mm) stem.



    spoke


    Nitto Column  

    Stems for 1 1/4" Threaded Forks

    Nitto MT Column SM1143

    buy button

    This is a quill adaptor that fits into a 1 1/4" threaded fork, and allows you to use any 1 1/8" threadless-type stem. Just the thing for Santana tandems!

     

    spoke

     

    Stem Raisers

    Stem Riser for threaded fork

    Stem Raisers for Standard Quill (post-type) Stems Stem Riser for threaded fork


    A stem raiser fits into the steering column in place of your present stem, and secures with a wedge bolt in the normal manner. The upper part of the stem raiser sticks out above the steerer, and is bulged out so that you can insert your original stem. The bottom of the original stem winds up a bit above the top of the headset, so you gain several inches of height.

    Overall length is 210mm. The bulged section is 100mm. Length to minimum insertion is 140mm.

    Part #For Stem with a Quill Diameter of:Diameter
    of inserted part of Raiser
    I.D. of bulged section of RaiserApplicationPrice
    SM24713/16" (21.15 mm)13/16" (21.15 mm)13/16" (21.15 mm) for older American bikes, BMX. buy button
    SM2487/8" (22.2 mm)7/8" (22.2 mm)7/8" (22.2 mm)fits most bikes with 1" threaded headsets (Most common). buy button
    SM2491.0" (25.4 mm)1.0" (25.4 mm)1.0" (25.4 mm)fits oversized forks with 1-1/8" threaded headsets. (Not very common).buy button
    Note: Steerers are butted at the bottom, so the hole in the steerer is constant-diameter until near the bottom, then the walls taper inward in the butted section. It is vitally important that the stem extender (or stem) is not inserted so far that the wedge is installed where the steerer is narrowing, or it could come loose unpredictably. This is sometimes a problem on smaller frames if you try to insert the stem or a stem riser too far down into the steerer.



    divider

    This site also features many
    useful articles by Sheldon Brown
    and others
    .

    Articles by Sheldon Brown and others
    Harris
    Home
    Beginners Brakes Commuting
    Lights
    Cycle-
    Computers
    Do-It-
    Yourself
    Essays
    Family
    Cycling
    Fixed Gear
    Singlespeed
    Frames Gears &
    Drivetrain
    Bicycle
    Humor
    Bicycle
    Glossary
    Bicycle
    Links
    Old
    Bikes
    Repair
    Tips
    Tandems Touring What's
    New
    Wheels Sheldon
    Brown
    divider

    Web site by Sheldon Brown

    URL: http://harriscyclery.com/head.html

    Copyright © 2005, 2008, 2011, 2012, 2013, 2014 Harris Cyclery

    Quantcast